Owner estimating business VoIP bandwidth needs

VoIP Bandwidth Requirements: How Much Your Business Needs

Stephanie Uncategorized

A business VoIP call needs roughly 31 to 87 kbps in each direction, depending on the codec, so a ten-person office with a handful of simultaneous calls needs well under 2 Mbps of upload and download set aside for voice. The number that decides call quality is rarely your plan’s headline speed. It is how much upload capacity is left for voice when everyone else in the office is also online.

This guide gives you the per-call figures, a formula you can run on a napkin, worked examples for 5, 10 and 20 simultaneous calls, and a short list of fixes when calls sound choppy. Talkroute runs on the devices your team already owns, so the only network question left is the one this page answers.

Talkroute
Manage business calls from anywhere
Talkroute handles business calls, texts, voicemail, and team communications on the devices your team already uses.

TL;DR

  • One VoIP call uses about 87 kbps each way with the common G.711 codec and about 31 kbps each way with G.729, according to Cisco’s bandwidth reference.
  • Size for simultaneous calls, not headcount: multiply peak concurrent calls by the per-call figure, then add 25% headroom.
  • Upload is usually the bottleneck on cable and DSL plans, so check your upload speed first, not your download speed.
  • Latency, jitter and packet loss spoil calls more often than a lack of raw speed. Prioritizing voice traffic on your router solves most problems.
  • Most small offices already have enough bandwidth. Test during your busiest hour to be sure.

Table of Contents

What bandwidth means for a phone call

Bandwidth is the amount of data your internet connection can carry per second. It is measured in kilobits per second (kbps) or megabits per second (Mbps), and 1 Mbps equals 1,000 kbps.

A phone call is a small, steady stream of data. Your voice is converted into digital packets, sent across the internet, and rebuilt at the other end. A codec is the method that compresses and decompresses that audio. Different codecs trade audio quality against data use, which is why the per-call figure is a range and not a single number.

Two things make VoIP sizing different from sizing for email or web browsing:

  1. Calls are two-way and constant. While you talk, one stream goes up from you and one comes down to you. Both must arrive on time.
  2. Timing matters more than volume. A web page that loads a second late is fine. A voice packet that arrives a fraction of a second late is useless and gets dropped, which you hear as a gap or a robotic sound.

How much bandwidth one VoIP call uses

The audio itself is small. The wrapping around it adds most of the load. Each packet carries headers that tell the network where it goes (IP, UDP and RTP headers), and a call sends 50 packets per second at the usual 20 millisecond packet size. Cisco’s engineers publish the math: the formula is total packet size multiplied by packets per second, and the figures below include the headers and standard Ethernet framing.

Codec Codec bit rate Bandwidth per call, each direction (Ethernet, 20 ms packets)
G.711 64 kbps 87.2 kbps
G.726 32 kbps 55.2 kbps
G.729 8 kbps 31.2 kbps
G.723.1 6.3 kbps 21.9 kbps

These figures come from Cisco’s voice bandwidth calculation reference. Two details matter for planning.

First, the figure is per direction. A G.711 call uses about 87 kbps of your upload and about 87 kbps of your download at the same time. Cisco’s design guidance notes that on a full-duplex link, which is how modern business internet works, a G.711 call consumes the equivalent of a single 87.2 kbps stream of the capacity in each direction, not double. That is why upload and download are sized separately.

Second, the headers are why a low-bit-rate codec does not shrink the call as much as you would expect. G.729 compresses the voice to 8 kbps, yet the call still uses 31.2 kbps once headers are added.

Some calls use larger packets, which lowers header overhead. Cisco’s contact center design guide shows G.729 falling to as low as 31.4 kbps for a full two-way call at 60 ms packets, compared with 62.4 kbps at 20 ms. The tradeoff is slightly more delay, so most business systems stay near 20 ms.

Per-call bandwidth compared across VoIP codecs

A planning number you can use

If you do not know which codec your system uses, plan on about 90 to 100 kbps per call in each direction. That covers G.711, the heaviest common choice, with a little room to spare. If your provider uses a lighter or variable codec, you will end up with slack, which is a better problem than a shortage.

The official speed guidance for a single call

The FCC’s Broadband Speed Guide lists VoIP calls at under 0.5 Mbps of download speed as a minimum for a call. That is a ceiling on what one call needs, and it confirms the picture above: a single call is tiny compared with video streaming or large file downloads.

The guide covers a single user. A business has several people on calls at once, plus laptops syncing files, so you need the formula in the next section.

How to calculate the bandwidth your office needs

Use four steps. The whole calculation takes five minutes.

Step 1: Estimate peak concurrent calls

Count the most calls that could be active in the same minute, not the number of employees. For many small offices, half of the staff on a call at the same moment is a cautious assumption. A sales team that lives on the phone may run higher. A team that mostly uses email and chat runs lower. Include every call path:

  • Desk or mobile app calls from staff
  • Calls waiting in an auto attendant or call queue that connect to staff
  • Video meetings, which use far more than voice
  • An AI receptionist answering at the same time as your team. If you add an AI receptionist for call handling, those calls count as concurrent calls too.

Step 2: Choose a per-call figure

Use 87.2 kbps for G.711 or 31.2 kbps for G.729 from the table above. When unsure, use 100 kbps.

Step 3: Multiply

Peak concurrent calls × per-call kbps = the upload you need, and the same figure for download.

Step 4: Add headroom

Add 25% on top. Calls are not the only thing on your network, packets get resent, and traffic spikes. Cisco’s guidance also says to provision for the worst case of continuous speech at full call bandwidth. Silence suppression, which stops sending packets during pauses, lowers average use, but it should not be what you plan around. The 25% figure is our planning rule of thumb, not an industry standard, and a larger buffer is harmless.

Worked examples

All examples use G.711 at 87.2 kbps per direction, the heavier choice, and 25% headroom.

Peak concurrent calls Raw, each direction With 25% headroom Same office on G.729 (31.2 kbps), with headroom
5 436 kbps 545 kbps 195 kbps
10 872 kbps 1,090 kbps (about 1.1 Mbps) 390 kbps
20 1,744 kbps 2,180 kbps (about 2.2 Mbps) 780 kbps
50 4,360 kbps 5,450 kbps (about 5.5 Mbps) 1,950 kbps

Example: a 12-person dental or law office. Six people on calls at peak is a reasonable estimate. Six × 87.2 = 523 kbps, and with 25% headroom that is about 654 kbps each way. A business internet plan with 10 Mbps of upload has roughly 15 times what voice needs.

Example: a 40-person home services company with dispatch. Assume 20 concurrent calls at peak. That is about 2.2 Mbps each way with headroom. Even a modest cable plan with 10 to 20 Mbps of upload covers it, as long as the rest of the office is not using the entire upload at the same moment.

The lesson from the table is that voice alone rarely needs much. Trouble starts when voice competes with something heavier.

Worked examples

Why upload speed is the number to check

Most cable and DSL plans advertise a large download speed and a much smaller upload speed. You might see 300 Mbps down and 10 to 35 Mbps up. Voice is symmetric: each call needs the same capacity both ways. So the smaller number, upload, is what you can actually count on.

Upload also gets used by things people forget about:

  • Cloud backups and file sync running during the workday
  • Video meetings, which send your video up continuously
  • Large email attachments and shared drive uploads
  • Security cameras that stream to a cloud service

If a backup uses all of your upload, the voice packets queue behind it and calls break up even though your plan is fast. This is the most common reason a business with plenty of nominal speed still has bad call quality.

How much extra to leave for video meetings

Video takes much more than voice. Optimum’s FAQ, drawing on Skype’s published figures, lists about 0.5 Mbps each way for a video call and 1.5 Mbps each way for HD video. One HD video meeting therefore uses as much upload as about 15 G.711 calls. If your team runs video meetings through Talkroute, which supports meetings of up to 100 participants, add each person who will be sending video from your office to your peak count at the video rate.

Latency, jitter and packet loss: the three quality measures

Speed is only part of the story. Three measurements tell you whether voice will sound clean.

  • Latency is how long a packet takes to arrive. A widely used guideline is to keep one-way delay under about 150 milliseconds. Beyond that, people start talking over each other.
  • Jitter is the variation in that delay. Voice packets must arrive evenly spaced. Under about 30 milliseconds of jitter is the common target.
  • Packet loss is the share of packets that never arrive. Under 1% is the usual target. Past a few percent, words go missing.

These are commonly cited targets rather than hard limits, and the right goal is simply to keep all three as low as possible. A connection can show excellent speed in a test and still have high jitter, so the speed number alone does not tell you how calls will sound.

How to test your connection the right way

  1. Run a speed test during your busiest hour, not at 7 a.m. when the office is empty. Note the upload number.
  2. Test over a wired connection first. Wi-Fi adds its own variation. If calls only break up on Wi-Fi, your wireless network is the problem, not your internet plan.
  3. Check jitter and packet loss, not only speed. Many free online tests report them alongside upload and download.
  4. Repeat on a few different days. Shared neighborhood cable connections slow down at peak times.
  5. Compare against your formula. If your measured upload is at least five times your calculated need, you have a comfortable margin.

What to do when calls sound choppy

Work through these in order. The first two fix most cases.

  1. Prioritize voice on your router. Quality of Service (QoS) settings tell your router to send voice packets ahead of bulk traffic like backups and downloads. Many business routers have a simple voice or VoIP preset.
  2. Schedule heavy uploads for after hours. Backups and large syncs should not run at 2 p.m.
  3. Move phones and computers off Wi-Fi where you can. Where Wi-Fi is needed, use the 5 GHz band and keep access points close to where people work.
  4. Restart or replace aging equipment. Old routers and switches become a bottleneck even on fast plans.
  5. Consider a separate connection for voice. If the office grows, a second internet line for voice and a main line for everything else removes the competition entirely.
  6. Call your internet provider if jitter or loss is high on a wired connection with nothing else running. That points to a line problem on their side.

Business internet versus home internet

Residential plans share capacity across a neighborhood and often have weak upload. Business-class plans usually offer higher upload, more stable performance and faster repair commitments, though the details depend on your provider and area. For a team of more than a few people who depend on the phones, a business plan with solid upload speed is inexpensive insurance. Fiber connections typically offer matching upload and download speeds, which suits voice well when it is available at your address.

Remote and hybrid teams add another variable: each person’s home network. Each remote worker only needs enough for their own calls, which is tiny, but a crowded home Wi-Fi network can still hurt quality. A wired connection or a router close to the work desk helps. Our guide on business phone systems for scaling and remote teams covers how distributed teams stay reachable.

Perspective

Most of the bandwidth worry we hear from small business owners comes from old advice written for hardware phone systems and dedicated lines. Today the question is much simpler. A call is a small, steady stream, and the formula in this article, concurrent calls times about 100 kbps plus headroom, gives you a number that a normal business internet plan clears many times over.

What we want owners to focus on instead is the thing that really breaks calls: other traffic crowding the upload. Fix that with a router setting and a backup schedule and you have solved the problem for good.

That is also why we built Talkroute to run on the phones and computers your team already has. There is no desk phone hardware to buy and no special line to install. Calls, texts, voicemail and meetings live in one app, so your network planning stays as short as the five-minute calculation above. If you are weighing cloud phones against other setups, our comparison of VoIP and UCaaS explains where each fits.

Paul

Get a phone system that fits the connection you have

Once you know your numbers, the phone system should be the easy part. Talkroute is a cloud business phone system with local and toll-free numbers, call routing, auto attendant menus, texting, voicemail with transcription and meetings in a single app. Plans start at $19 per month for Basic, with Plus at $39 per month and Pro at $59 per month, and extra users cost $5 per month each. You can compare every plan on the Talkroute pricing page.

Talkroute

If your office is growing or you want to understand how cloud calling works before you decide, read our overview of cloud telephony and how it works.

FAQ

How much bandwidth do I need for VoIP?

Plan on about 100 kbps of upload and 100 kbps of download for every call happening at the same moment. For a small office with 5 to 10 concurrent calls, that is roughly 0.5 to 1.1 Mbps each way once you add 25% headroom. Video meetings need more, so count them separately.

What upload speed do I need for VoIP?

Multiply your peak concurrent calls by about 100 kbps and add 25%. Ten simultaneous calls need around 1.25 Mbps of upload reserved for voice. Because backups and video meetings also use upload, many offices aim for an upload speed several times larger than that figure.

Is 100 Mbps fast enough for a small business phone system?

Almost certainly, for voice. Even 50 concurrent calls need only about 5.5 Mbps each way with headroom. What matters more is the upload portion of that plan and whether your router prioritizes voice, since a fast download speed does not guarantee clean calls.

Does the codec change how much bandwidth I use?

Yes. According to Cisco, G.711 uses about 87.2 kbps per direction and G.729 about 31.2 kbps, so the lighter codec uses roughly one third as much. For most small offices the difference does not matter, because both fit easily inside a typical business connection.

Do I need a dedicated internet line for VoIP?

Not for most small businesses. A single business-class connection with enough upload and a router set to prioritize voice is usually sufficient. A separate line becomes worth considering when call volume is high or heavy uploads keep interfering with voice.

Sources

Stephanie

Stephanie is the Marketing Director at Talkroute and has been featured in Forbes, Inc, and Entrepreneur as a leading authority on business and telecommunications.

Stephanie is also the chief editor and contributing author for the Talkroute blog helping more than 200k entrepreneurs to start, run, and grow their businesses.

StephanieVoIP Bandwidth Requirements: How Much Your Business Needs